I'd suggest a Micro or a Teensy. They have all of those interfaces plus a USB interface so that you can view/control the thing easily from your PC. The Teensy has two additional serial UARTs, a second I2C port and CAN bus too. A Due or Mega would also work.
Mini-Circuits’ U2C-1SP2T-63VH is a high isolation, high power, absorptive SPDT switch with USB, I2C and SPI control. The fast The fast switching, solid state switch operates from 10 MHz to 6000 MHz with 700 ns typical ransition time.
USB-Serial Dual Channel (UART/I2C/SPI) Bridge with CapSense® and BCD Features USB2.0 certified, Full-Speed (12Mbps) Support for communication driver class (CDC), personal health care device class (PHDC), and vendor device class Battery charger detection (BCD) compliant with USB Battery Charging Specification Rev 1.2 (Peripheral Detect only)
The "I2C/SPI" tab is useful for communicating with generic I2C and SPI devices; in case of I2C it's always necessary to specify the control byte (and address, if not zero); RW bit is handled automatically. For example, to write manually 3 bytes on a 24xx16 at address 64 write: A0 40 1 2 3
UART/Serial USB converter, up to 12Mbps (depending on the FTDI device capability) GPIO/Bitbang support, with 8-bit asynchronous, 8-bit synchronous and 8-/16-bit MPSSE variants SPI master, with simultanous GPIO support, up to 12 pins per port, with support for non-byte sized transfer
The USB-910H Embedded Systems Interface provides connectivity between a host PC and I2C, SMBus, or SPI. Other interfaces can be supported by "bit-banging" the 9 general-purpose I/O. USB transactions are generated on the host PC using either the Keterex USB-900 Control Center application or custom software via calls to the provided API.
- Up to two SPIs (18 Mbit/s) with 4 to 16 programmable bit frames, one with I2S interface multiplexed. - USB 2.0 full-speed interface, able to run from internal 48 All devices offer standard communication interfaces (one I2C, two SPIs/one I2S, one HDMI CEC and two USARTs), one USB Full-speed device...
Nov 03, 2020 · The USB-8451 is a VISA Resource and appears in Measurement & Automation Explorer (MAX) in the USB Devices section. It is assigned a standard VISA resource descriptor. This allows you to use the VISA Find Resources VI in LabVIEW to determine if the USB-8451 is present in the system.
The 'bus mode' menu (M) configures the Bus Pirate for a specific protocol, like 1-Wire, I2C, SPI, etc. The default start-up mode is HiZ, all pins are inputs and all power supplies are off. Most modes have additional options, like open drain outputs or speed settings. Each bus mode is documented in the Bus Pirate manual. SPI READY
All in 1 CH341A USB to SPI I2C IIC UART TTL ISP Serial Adapter Module EPP MEM Converter for Serial Brush Debugging RS232 RS485 CDN$ 27.25 CDN$ 27. 25 USB to I2C USB to RS232 USB to Serial USB Converter Promotional Package CDN$ 31.50 CDN$ 31 . 50
Sep 05, 2019 · Re: USB protocols over SPI, I2C, Serial? Problemchild Sep 5, 2019 9:40 AM ( in response to michaelkellett ) I think the solution he's proposing is a little more generic and would need to support the USB's multi endpoint provision.
May 16, 2017 · I2C is commonly used for sensors like accelerometers that don't need high data rates. LED drivers, temperature sensors, that sort of thing. USB : For programming you can use USB only because there's a bootloader program already on the chip that sets the system up, receives the binary, and does the actual programming.
Fixed power sequencing issue. I2C works, SPI only does single byte transactions. 4:bf2b2b0cd5d3: 2016-12-08: switches: Committing alpha release for sharing 3:aa55728c8e09: 2016-12-08: switches: USB serial adapter enables communication with I2C and SPI devices over USB. 2:57500e991166: 2016-12-08: switches
The Beagle USB 5000 v2 analyzer is the premier choice for any developer looking to debug and develop USB 3.0 and USB 2.0 systems easily and efficiently. Beagle ™ USB 5000 v2 SuperSpeed Protocol Analyzer. FAST • Save time with fast capture, upload, and filtering times on the most efficient USB 3.0 and USB 2.0 analysis platform and USB 3.0 ...

Aerway sportstine

USB-to-Dual Channel (I2C/SPI) Bridge on page 22). I2C Interface The I2C interface implements full multi-master/slave modes and supports up to 400 kHz. The configuration utility tool is used to set the I2C address in slave mode. This tool enables only even slave addresses. For further details on protocol, refer to the NXP I2C specification rev5 ...

Visita eBay per trovare una vasta selezione di usb to spi. Scopri le migliori offerte, subito a casa, in tutta sicurezza. FT2232 HL USB a UART FIFO di serie Interfaccia periferica I2C JTAG RS232/RS422/RS485 Modulo.
Wanderer wagon toy hauler specsUsing C# to control individual pin states of FTDI USB-to-serial converters, I can bit-bang SPI devices! Here I demonstrate how to ... If you are looking for a hassle free way to enhance your product with an USB interface, the new CP2130 USB-to-SPI bridge is ...
Zoho crm project management

This module provides a USB adapter, that opens up communication with I2C, SPI, UART and parallel connections. These options make for an ideal microcontroller programming interface. The mode of operation is selected via the use of an onboard jumper.
Day countdown app

Sep 05, 2019 · Re: USB protocols over SPI, I2C, Serial? Problemchild Sep 5, 2019 9:40 AM ( in response to michaelkellett ) I think the solution he's proposing is a little more generic and would need to support the USB's multi endpoint provision.

Icims withdraw button

Bond order of ne2 2
Taylor swift all you had to do was stay
I2C (Inter-Integrated Circuit), pronounced I-squared-C, is a synchronous, multi-master, multi-slave, packet switched, single-ended, serial communication bus invented in 1982 by Philips Semiconductor (now NXP Semiconductors).
Saturn recalls
Entire USB protocol handled on the chip. No USB specific firmware programming required. USB 2.0 Hi-Speed (480Mbits/Second) and Full Speed (12Mbits/Second) compatible. Multi-Protocol Synchronous Serial Engine (MPSSE) to simplify synchronous serial protocol (USB to JTAG, I2C, SPI (MASTER) or bit-bang) design. › See more product details USB to I2C / SPI / UART / GPIO bridges with higher Performance. Sep 13, 2019 ... USB camera module to MCU via SPI/I2C adapter. Thread starter Jase009; Start date Nov 29, 2019; Search Forums; New Posts; J. Thread Starter. Jase009. Joined Aug 27 ... .